BMR 82-02 3rd Gen F-Body Rear Hollow 25mm Sway Bar Kit w/ Bushings - Red - Bull Strap
BMR 82-02 3rd Gen F-Body Rear Hollow 25mm Sway Bar Kit w/ Bushings - Red - Bull Strap

BMR 82-02 3rd Gen F-Body Rear Hollow 25mm Sway Bar Kit w/ Bushings - Red

$271.87
In Stock Pre order Out of stock
Add to Wishlist
Details
The two primary functions of sway bars are to control body roll and to determine the understeer or oversteer behavior of a vehicle. Stock sway bars have low torsional spring rates because they are manufactured from small diameter bar stock or tubing. BMR Suspensions SB003 rear sway bar was designed by factoring in the vehicle weight, application, motion ratio, coil spring rate, and adjustability requirements. Manufactured from heavy-wall 25mm DOM tubing, the SB003 is cold formed to better resist torsional fatigue and retain its "memory" far longer than the hot-formed bars used by many competitors. The sway bar is CNC-formed for exact manufacturing tolerances and repeatable high quality. The SB003 attaches to your Camaro with 88-durometer polyurethane bushings, reducing the deflection from the stock rubber bushings. These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keeps grease in the bushing. The fabricated laser cut, TIG-welded steel sway bar end links are reinforced to minimize deflection. BMR Suspension designed the SB003 sway bar for street performance, drag race, autocross, and road race applications. The SB003 gives you a 149% increase in rate over the stock bar (depending on year and model). These rate increases allow you to fine-tune the handling characteristics of the suspension so you can drive harder through corners with minimal body roll. The hollow design allows for loads of strength without adding a lot of weight. This allows for more sway bar control, which equals better handling. When performance is a must, rely on BMR Suspension! BMR Suspensions SB003 sway bars are available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.! All kits come with polyurethane mounting bushings and endlink kits.
Application Guide


This Part Fits:

Year Make Model Submodel
1988,1993-2002 Chevrolet Camaro Base
1982-1986 Chevrolet Camaro Berlinetta
1993 Chevrolet Camaro Indianapolis 500 Pace Car
1985-1990 Chevrolet Camaro Iroc-Z
1987 Chevrolet Camaro LT
1989-1992,1996-1997 Chevrolet Camaro RS
1992 Chevrolet Camaro RS Heritage Edition
1982-1987 Chevrolet Camaro Sport
1982-1987,1991-2002 Chevrolet Camaro Z28
1992 Chevrolet Camaro Z28 Heritage Edition
1982 Chevrolet Camaro Z28 Indianapolis 500 Pace Car
1998-2002 Chevrolet Camaro Z28 SS
1982-2002 Pontiac Firebird Base
1989-2002 Pontiac Firebird Formula
1982-1986 Pontiac Firebird S/E
1982-2002 Pontiac Firebird Trans Am
1994 Pontiac Firebird Trans Am GT
1989-1992 Pontiac Firebird Trans Am GTA
1989 Pontiac Firebird Trans Am GTA SE
Refund Policy

Bull Strap products are the highest grade cut and sewn items in the automotive industry. We are proud to support USA workers in our bid to manufacture right here in the United States.

WARRANTY

Bull Strap guarantees all products to be free from manufacturer defects for all items for one year, and any color fading (where mentioned) for 2 years from the time of purchase. In the event of a product failure, Bull Strap will decide whether that product should be repaired or replaced after reviewing photos submitted by the customer. Bull Strap will then provide a return shipping label for any product in which the material or stitching were determined to be the root cause. Once received, the product will be repaired or replaced and returned to the customer at no cost.

REFUND POLICY

Seat covers and other custom made items, retain all warranties listed above, but cannot be refunded or exchanged at any time

On non-custom items, if within 30 days of purchase directly from Bull Strap, a customer would like to return an unused product with no modifications, and where the item(s) can be considered 'new in box', the customer can email us at info@bullstrap.com or call us at 951-319-4008. The will be a 15% restocking fee subtracted from any returned items. Once processed, the customer must ship the product back and submit the tracking information. Bull Strap will issue a full refund minus the 15% restocking fee once the item(s) is/are received and determined to be in 'Brand New' condition. NOTE: If a customer ordered Bull Strap products from a dealer, the customer must go through this process directly with the dealer the product was ordered from.

As always, we strive to provide the best product and customer service available...but we are definitely not perfect. If at any time, you have any issues, please contact us, so we can address any problems you may have. Thanks!

Shipping Policy

Coming Soon

Customer Reviews

Be the first to write a review
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)